Type R = rugged (Installed loads up to 25 kg) with integrated, tox-cold welded 19" mounting bracket and higher material thicknesses for extreme mechanical stresses, e.g. for increased shock and vibration environments up to 25 g
For indirect backplane mounting with insulation strip
For direct backplane mounting
For direct fixing of connectors in accordance with EN 60603-2 (DIN 41612)
Perforated Al plate, 1.2 mm, hole diameter 3.8 mm, AI, untreated, perforation degree 60 %; for insertion into the groove of the light horizontal rails
Standard dimentions: Width - 42,63,84HP; Depth - 175mm (for 160 mm board depth), 235mm (for 220 mm board depth)
Custom dimensions on request
Cover plate for bolting to side panel;
Used when standard-depth PCBs (160, 220, 280, ...) are fitted;
AI, 1.0 mm, hole diameter 4.0 mm, passivated, perforation degree 58 %; for shielding 4 stainless steel EMC gaskets are required per subrack
stainless steel EMC gasket, clips into the horizontal rail and forms the contact with the cover plate; suitable for all horizontal rails
Installed on the inside of the front rail to form a good conductivity between the panel and the rail, this increasing the shielding effect
Material: Stainless steel
The seal is affixed to left side if the subrack or to the U-profile front/rear panel;
Assures a long-term high level of shielding, typically 40 dB at 2 GHz;
Material: Conductive cloth EMC fabric gasket;
Core: TPE foam
Temperature range: -40° C to +70° C
Assures a long-term high level of shielding, typically 40 dB at 2 GHz;
Material: stainless steel, beryllium bronze;
Temperature range: -200° C to +160° C
Guide rails form the interface between the subrack mechanics and the sub-assemblies (PCB boards, plug-in units, frame-type plug-in units, ...).
Guide rails for standard applications are 2 HP wide. Guide rails with coding (e.g. for CompactPCI or VME64bus applications) are 4 HP wide.
There are groove widths of 2 mm and 2.5 mm.
The guide rails are clipped into the rectangular cut-outs of the horizontal rails. They can additionally be bolted to the horizontal rail (type Heavy only) for higher shock and vibration requirements (Torque max. 0.2 Nm).
The printed HP markings on the horizontal rail allow the rails to be fitted in the correct position easily (position of sub-assembly = "number in viewing window" or in front of the arrow marking on the guide rails).
For reliable retention of PCBs, plug-in units and frame type plug-in units
Type: Standard
For reliable retention of PCBs, plug-in units and frame type plug-in units
Type: Short
For reliable retention of PCBs, plug-in units and frame type plug-in units
Type: Reinforsed
For especially heavy PCBs, plug-in units or frame type plug-in units
Type: Heavy
For for CompactPCI, VME64x application
with 0.1" OFFSET for power supply units
Type: CPCl
ensures conductive contact between PCB and horizontal rail both on the solder side and on the component side;
Material: Spring steel, tin-plate
accordance with IEEE;
can be plugged into the guide rails withcoding and into the keying/coding block;
provides conductive contact between the alignment pin of the insertion/extractor handle (IEL or IET handle) and the horizontal rail;
Material: Spring steel, tin-plate
Top and Bottom keying/coding block is clipped into the horizontal rail next to the guide rail;
Color: Red;
Keying only possible in conjunction with IEL/ IET handles and coding pegs;Can only be used in combination with guide rails "Short" type;
Possible application on top and bottom horizontal rail;For fixing PCB in a subrack or 19" case
Material: PBTP; UL94V-0, RedSplitting extrusion is inserted in the grid holes of the horizontal rail;
The splitting extrusion can be bolted;
Splices are used for combined installation in a single box;
The front of the chassis must be covered with a 2HP front panel;
Material: Aluminum alloy die-casting;
Surface treatment: galvanized
Unshielded Flat front panel 6 U, 2 HP, Al, 2.5 mm;
U-profile front panel 6 U, 2 HP, Al, 2.5 mm, Prepared for textile EMC gasketInstalled on the front flange or side panel of the subrack;
Load-carrying capacity 30 kg;
AI extrusion, anodised clear/black;
Width 12.2mm;
Screw M5 x 12, Torque max. 2,4 N·m (ordered separately)Installed on the front flange or side panel of the subrack;
Load-carrying capacity 30 kg;
Hole distance: 320mm, 224mm, 192mm, 160mm, 120mm, 96mm, 88mm, 55mm
Heigth 35mm;
Handle diameter 10mm;
Screw ordered separatelyFixing Material for Subracks